factory menu paint roller search lock profile switch star remove

Industrial Paints & Protective Coatings

“We have your application covered”

Agricultural

13-3 Rapidac Matt Black

Single pack modified alkyd coating that is fast drying with a matt black industrial finish for use on mild steel components, wrought iron and similar applications.

  • Overcoating Time @ 20°C : May be overcoated when firm dry but within 1 hour or allow to dry overnight. Overcoating and drying times will depend on ambient temperatures and especially ventilation, air movement, etc.
  • Touch Dry @ 20°C: 20 minutes

40 Low Odour Metal Primer

Single pack low odour primer with good adhesion and durability

  • Overcoating Time @ 20°C : Overnight
  • Touch Dry @ 20°C: 2 hours
  • Colour: Red Oxide or Grey

510 QD3 Quick Drying Gloss Enamel

Single pack modified alkyd fast drying gloss finish for general metal work. Rapid hardening with good adhesion

  • Overcoating Time @ 20°C : Should a second coat of QD3 be required, this must be applied within 2 hours of the first coat to avoid lifting or wrinkling of the QD3. After this 2 hour period, the QD3 will require at least 10 days curing before becoming resistant to solvents in the second coat
  • Touch Dry @ 20°C: 15 minutes
  • Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

524 Implamel One Coat Sheen Primer/Finish

Single pack general purpose 'one coat' primer/finish for structural steelwork, waste skips and similar steel fabrications.

  • Overcoating Time @ 20°C : Should a second coat be required, allow a minimum of 4 hours drying or preferably leave overnight between coats. The maximum over coating time is indefinite and is subject to normal good housekeeping practices for preparation an cleanliness between coats.
  • Touch Dry @ 20°C: 20 minutes
  • Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

581 Two Pack Acrylic Gloss or Semi Gloss Finish

Two pack acrylic finish , excellent durability, colour and gloss retention, chemical resistance.  Isocyanate free.

  • Overcoating Time @ 20°C : Where a further coat of Acrylic Finish is required, this should be applied as soon as the first coat is touch-dry or, allow the first coat to dry for not less than 48 hours before overcoating.
  • Touch Dry @ 20°C: 1 hour
  • Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

585 Two Pack HS Polyurethane Gloss Finish

Two pack high solids polyurethane gloss finish, chemical resistant, excellent colour and gloss retention, compliant to Environmental Protection Act (1990) as required by Guidance Note PG6/23 (97), (Clause 20 (d).  Conforms to Highways Agency Specification Item 168.

  • Overcoating Time @ 20°C : N/A
  • Touch Dry @ 20°C: 2 hours
  • Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

591 UHB Tinted High Build Anti Corrosion Primer

Single pack or two pack high build primer (two pack when used with 591 GP Hardener/Activator)


  • Overcoating Time @ 20°C : 1 1/2 hours
  • Touch Dry @ 20°C: 10 minutes
  • Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

597 Vehicle & Machinery Gloss Enamel

Single pack modified alkyd finishing coat for vehicles, plant and machinery. Excellent durability with good resistance to oils, grease and similar. Dries to hard film with hard abrasion and impact resistance.

  • Overcoating Time @ 20°C : Should a second coat of Vehicle and Machinery Enamel be required, this can be applied as soon as the first coat is touch dry, ie. up to 1 hour - or allow coating to dry overnight.
  • Touch Dry @ 20°C: 1 hour
  • Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

79-458 Epidac 2 High Build Zinc Phosphate Primer

Two pack high build epoxy with anti corrosion pigmentation for use on prepared steel and galvanised steel.

Fully compliant to Environmental Protection Act (1990) as required by Guidance Note PG 6/23 (97), Clause 20 (d), when used as tie coat, sealer or blast primer.

  • Overcoating Time @ 20°C : Overnight
  • Touch Dry @ 20°C: 2-4 hours
  • Colour: Grey

95-56 Glodac Basecoat

Single pack modified urethane as a white basecoat to give fluorescent colour when overcoated with Glodac fluorescent paints.

  • Overcoating Time @ 20°C : Overnight
  • Touch Dry @ 20°C: 2 hours
  • Colour: White

97- Glodac Daylight Flourescent Paint

Flourescing pigement in alkyd media typically used on safety barriers, hazard warning signs where a bright flourescent effect is required.

  • Overcoating Time @ 20°C : Overnight
  • Touch Dry @ 20°C: 1 hour

97-107 Glodac Overlacquer

Glossy silicone alkyd lacquer for Glodac flourcescent coating to prolong colour and brightness on exterior exosure.

  • Touch Dry @ 20°C: 1 hour
  • Colour: Clear Gloss

98 Quick Drying Anti Corrosion Primer

Single pack fast drying primer using modified alkyd, zinc phosphate with good rust-inhibitive properties suitable for the protection of steel. 

  • Overcoating Time @ 20°C : Maybe overcoated after 45 minutes or as soon as film-dry with all white spirit based finishing coats. Fast-drying finishing coats based on stronger solvents should be overcoated when primer is firm-dry but within 1 hours, or allow primer to dry overnight (refer to data sheet)
  • Touch Dry @ 20°C: 30 minutes
  • Colour: Black, White, Grey-Green, Buff, Cupress, Red Oxide, Yellow, Blue, Grey, other colours to special order

Corroless S

 Single pack rust stabilising primer.  Can be applied to steelwork where blasting is not possible, manually prepare to ST2  standard of EN ISO  8501-1:2007.  Over 30 years track record in corrosion control.  Will withstand operating temperatures of up to 200 Deg C.

  • Colour: S1 Red Brown S2 Buff
 
Showing 1 to 14 of 14 (1 Pages)
×

Join Our Newsletter

Signup today for free.