581 Two Pack Acrylic Gloss or Semi Gloss Finish

Two pack acrylic finish , excellent durability, colour and gloss retention, chemical resistance.  Isocyanate free.

• Overcoating Time @ 20°C : Where a further coat of Acrylic Finish is required, this should be applied as soon as the first coat is touch-dry or, allow the first coat to dry for not less than 48 hours before overcoating.
• Touch Dry @ 20°C: 1 hour
• Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

585 Two Pack HS Polyurethane Gloss Finish

Two pack high solids polyurethane gloss finish, chemical resistant, excellent colour and gloss retention, compliant to Environmental Protection Act (1990) as required by Guidance Note PG6/23 (97), (Clause 20 (d).  Conforms to Highways Agency Specification Item 168.

• Overcoating Time @ 20°C : N/A
• Touch Dry @ 20°C: 2 hours
• Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

591 UHB Tinted High Build Anti Corrosion Primer

Single pack or two pack high build primer (two pack when used with 591 GP Hardener/Activator)

• Overcoating Time @ 20°C : 1 1/2 hours
• Touch Dry @ 20°C: 10 minutes
• Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

597 Vehicle & Machinery Gloss Enamel

Single pack modified alkyd finishing coat for vehicles, plant and machinery. Excellent durability with good resistance to oils, grease and similar. Dries to hard film with hard abrasion and impact resistance.

• Overcoating Time @ 20°C : Should a second coat of Vehicle and Machinery Enamel be required, this can be applied as soon as the first coat is touch dry, ie. up to 1 hour - or allow coating to dry overnight.
• Touch Dry @ 20°C: 1 hour
• Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

599 Dacthane Gloss Enamel

Single pack  urethane alkyd finishing coat for vehicles, plant and machinery. Excellent durability with good resistance to oils, grease, etc. Dries to tough film with high abrasion and impact resistance.

Dacthane finishes from the Dacmix scheme are 'Compliant' to Environmental Protection Act (1990) Clause 20(d) of Guidance Note PG6/23 (97).

• Overcoating Time @ 20°C : Should a second coat of Dacthane Enamel be required, this can be applied as soon as the first coat is touch dry, ie. up to 2 hours - or allow coating to dry completely for at least 16 hours.
• Touch Dry @ 20°C: 2 hours
• Colour: Tinted to any BS4800/Ral/BS381C or bespoke colour

79-458 Epidac 2 High Build Zinc Phosphate Primer

Two pack high build epoxy with anti corrosion pigmentation for use on prepared steel and galvanised steel.

Fully compliant to Environmental Protection Act (1990) as required by Guidance Note PG 6/23 (97), Clause 20 (d), when used as tie coat, sealer or blast primer.

• Overcoating Time @ 20°C : Overnight
• Touch Dry @ 20°C: 2-4 hours
• Colour: Grey

98 Quick Drying Anti Corrosion Primer

Single pack fast drying primer using modified alkyd, zinc phosphate with good rust-inhibitive properties suitable for the protection of steel. 

• Overcoating Time @ 20°C : Maybe overcoated after 45 minutes or as soon as film-dry with all white spirit based finishing coats. Fast-drying finishing coats based on stronger solvents should be overcoated when primer is firm-dry but within 1 hours, or allow primer to dry overnight (refer to data sheet)
• Touch Dry @ 20°C: 30 minutes
• Colour: Black, White, Grey-Green, Buff, Cupress, Red Oxide, Yellow, Blue, Grey, other colours to special order